30 mhz to 1000 mhz 75 gain block preliminary technical data adl5533 rev. prc 5/07 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2007 analog devices, inc. all rights reserved. features fixed gain of 20 db operation up to 1000 mhz +37.3 dbm oip3 at 70 mhz noise figure 2.9 db at 70 mhz input/output internally matched to 75 temperature and power supply stable power supply: 5 v power supply current: 66 ma 1000 v esd (class 1c) functional block diagram adl5533 5clin 8nc nc 4 6nc rfin 2 7rfout nc 3 nc 1 figure 1. block diagram general description the adl5533 is a fixed-gain, linear amplifier that operates at frequencies up to 1000 mhz. intended for use in a wide variety of applications, including broadband, catv, cable modem and ftth. the fixed gain of 20 db is stable over frequency, temperature, power supply and from device to device. oip3 is +37.3 dbm with an output compression point of +18.8 dbm and a noise figure of 2.9 db. the adl5533 is single-ended and internally matched to 75 with an input return loss of 10 db. only input/output ac- coupling capacitors, a power supply decoupling capacitor and external inductor are required for operation. this amplifier operates with a supply voltage of +5v, consuming 66 ma of supply current. the adl5533, fabricated on a gaas hbt process, and has an esd rating of 1000 v (class 1c).the device is packaged in a 3mm x 3mm lfcsp that uses an exposed paddle for excellent thermal impedance and operates from ?40c to +85c. a fully populated evaluation board is available.
adl5533 preliminary technical data rev. prc 5/07 | page 2 of 9 table of contents features .............................................................................................. 1 functional block diagram .............................................................. 1 general description ......................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 absolute maximum ratings ............................................................ 4 esd caution ...................................................................................4 pin configuration and function descriptions ..............................5 typical performance characteristics ..............................................6 evaluation board ...............................................................................7 outline dimensions ..........................................................................9 ordering guide .............................................................................9 revision history 5/07rev. prc: preliminary version
preliminary technical data adl5533 rev. prc 5/07 | page 3 of 9 specifications v cc = 5 v, t = 25c, unless otherwise noted. table 1. parameter conditions min typ max unit overall function frequency range 30 1000 mhz gain vs. frequency 50 mhz. center frequency = 190 mhz or 380 mhz 0.25 db input return loss (s11) 50 mhz to 750 mhz -10 db output return loss (s22) 50 mhz to 750 mhz -10 db frequency = 70 mhz gain 19.8 db vs. temperature ?40c t a +85c .25 db output 1 db compression point 18.7 dbm output third-order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) 37.3 dbm output second order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) tbd dbm noise figure 2.9 db frequency = 380 mhz gain 18.6 db vs. temperature ?40c t a +85c .25 db output 1 db compression point 18.8 dbm output third-order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) 35.7 dbm output second order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) tbd dbm noise figure 3.1 db frequency = 820 mhz gain 16.8 db vs. temperature ?40c t a +85c .25 db output 1 db compression point 18.3 dbm output third-order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) 34.5 dbm output second order intercept ?f = 1 mhz, output power (p out ) = 0 dbm (per tone) tbd dbm noise figure 3.2 db power interface pins rfout,vcc supply voltage 4.75 5 5.25 v supply current 66 ma vs. temperature ?40c t a +85c 75 ma power dissipation vpos = 5v 330 mw
adl5533 preliminary technical data rev. prc 5/07 | page 4 of 9 absolute maximum ratings table 2. parameter rating supply voltage, vpos 5.5 v input power (re: 75 ) +12 dbm internal power dissipation (paddle soldered) 650 mw ja (paddle soldered) tbd c/w maximum junction temperature tbd c operating temperature range ?40c to +85c storage temperature range ?65c to +150c (soldering 60 sec) 240c stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
preliminary technical data adl5533 rev. prc 5/07 | page 5 of 9 pin configuration and fu nction descriptions 5clin 8nc nc 4 6nc rfin 2 7rfout nc 3 nc1 pin 1 indicator top view (not to scale) adl5533 figure 2. pin configuration table 3. pin function descriptions single pin o. nemonic description 2 rfin rf input: requires a dc blocking capacitor. 7 rfout rf output and bias: dc bias is provided to this pin through an inductor. rf path requires a dc blocking capacitor. 1, 3, 4, 6, 8 nc no connect 5 clin a 10 nf capacitor connected between pin 5 and ground provides decoupling for the on board linearizer. exposed paddle internally connected to gnd. solder to a low impedance ground plane
adl5533 preliminary technical data rev. prc 5/07 | page 6 of 9 typical performance characteristics 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 50 150 250 350 450 550 650 750 850 950 1050 frequency (mhz) nf,gain, p1db, oip3 (db, dbm) nf gain p1db oip3 figure 3 adl5533 gain, noise figure, oip3 and p1db vs frequency 20 22 24 26 28 30 32 34 36 38 40 42 -6-4-202468101214161820 pout (dbm) oip3 (dbm) 70 mhz 190 mhz 380 mhz 500 mhz 820 mhz 1000 mhz figure 4 adl5534 oip3 vs pout and frequency -35 -30 -25 -20 -15 -10 -5 30 130 230 330 430 530 630 730 830 930 1030 frequency (mhz) returnloss & isolation (db) s11 s12 s22 figure 5 adl5533 input / output return loss and reverse isolation vs frequency
preliminary technical data adl5533 rev. prc 5/07 | page 7 of 9 evaluation board figure 6 shows the schematic for the adl, 5533 evaluation board. the board is powered by a single 5 v supply. the components used on the board are listed in. table 4 power can be applied to the board through clip-on leads (vcc, gnd), or through jumper w1. adl5533 1 2 3 4 8 7 6 5 rfin rfout nc nc nc clin c3 100 nf l1 470 nh c2 10 nf c4 10 nf c5 1 uf w1 vc c gnd testloop red testloop black rfout c1 10 nf rfin nc nc 6.8 nh l2 c6 open c7 open figure 6. evaluation board schematic table 4. evaluation board configuration options component function default value c1, c2 ac-coupling capacitors. 10 nf 0402 c3, compensates for internal non linearities c3 100 nf 0603 c4, c5 power supply decoupling capacitors capacitor. c4 10 nf 0603 c5 1uf 0603 c6, c7 open 0603 l1 dc bias inductor. 470 nh l0603 l2 output matching element. 6.8 nh l0603 vcc & gnd clip-on terminals for power supply. vcc red gnd black rfin, rfout rf input and output interface 75 ohm f type connectors w1 2-pin jumper for connection of ground and supply via cable.
adl5533 preliminary technical data rev. prc 5/07 | page 8 of 9 figure 7. evaluation board layout (top) figure 8.evaluation board layout (bottom)
preliminary technical data adl5533 rev. prc 5/07 | page 9 of 9 outline dimensions 022107-a 1 exposed pa d (bottom view) 0.50 bsc 0.60 max pin 1 indicator 0.50 0.40 0.30 top view 12 max 0.70 max 0.65 typ 0.90 max 0.85 nom 0.30 0.23 0.18 0.05 max 0.01 nom 0.20 ref 1.89 1.74 1.59 4 1.60 1.45 1.30 3.25 3.00 sq 2.75 2.95 2.75 sq 2.55 5 8 pin 1 indicator figure 9. 8-lead lead frame chip scale package [lfcsp_vd] 3mm 3 mm body, very thin, dual lead cp-8-2 dimensions shown in millimeters ordering guide model temperature range package description package option branding ordering quantity adl5533acpz-r7 1 ?40c to +85c 8-lead lfcsp tape and reel cp-8-2 adl5533acpz-wp 1 ?40c to +85c 8-lead lfcsp waffle pack cp-8-2 ADL5533-EVALZ evaluation board 1 z = pb-free part. ?2007 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. pr06835-0-5/07(prc)
|
